Our webstore uses cookies to offer a better user experience and we recommend you to accept their use to fully enjoy your navigation.
Manufacturers
M2 White Plastic Hexagonal Pillar (20 mm)
Thermocouples are very sensitive, requiring a good amplifier with a cold-compensation reference, as well as calculations to handle any non-linearities. See description for more details about the product. Add to cart now!
M2 White Plastic Hexagonal Pillar (6 mm)
The Radiolink OSD Telemetry Module (Pixhawk & APM) transmits the data from the flight controller and shows the data of SPEED, RISE, THRO, VOLT, LATI, LONG, ALT, GPS, RSSI, MODE, YAW, ROLL, PITC, DIST in the display screen of AT9 or AT10. See description for more details about the product. Add to cart now!
With this module, you can listen to music from different devices. Supports A2DP and AVRCP. It has functions like play / pause and volume control of the device to which it is connected. Supports two devices connected at the same time. See description for more details about the product. Add to cart now!
AD8495 Thermocouple Amplifier Module
Infrared Remote Control Receiver Module 38 KHz
1.44" LCD Module (128x128 px) Red
Power Supply: 3.3 to 5v Interface: 3 wire SPI Accuracy: 0.25 degree temperature Compatible Thermocouple: K type Measurement Temperature Range: -200 °C to 1350 °C Resolution: 14 bit See description for more details about the product. Add to cart now!
This module is based on the AD8594 amplifier which allows you to read the temperature on a wide range of values from different thermocouple sensors. The gain is around 5 mV/oC. See description for more details about the product. Add to cart now!
10*6 mm White M3 Hex Pillar See description for more details about the product. Add to cart now!
12*5 mm Plastic White M3 Hex Pillar
Raspberry Pi Camera Module 2 See description for more details about the product. Add to cart now!
M2 Black Plastic Hexagonal Pillar (7 mm)
M2 Black Plastic Hexagonal Pilar (6 mm)
M2 Black Plastic Hexagonal Pilar (5 mm)
Model: FR120N MOS tube: 100V 9.4A Dimensions: 34 mm X 16mm Mounting Holes Diameter: 2mm Compatible with MCU and control board, 3V or 5V signal. High-level start, low-level stop, PWM speed regulation. See description for more details about the product. Add to cart now!
Original product
Pinbetween gives you access to all of the micro:bit's pins at the same time as using an edge-connector add-on, and it's completely solderless! See description for more details about the product. Add to cart now!
0.96 inch diagonal OLED screen module with a resolution of 128 x 64 pixels. See description for more details about the product. Add to cart now!
1.44" SPI LCD Module (128 x 128) ST7735 (Black), 7 pin
This module is the perfect way to add LCD with a small screen to add brilliance to your project. Easy to use with any microprocessor, even small ones with less memory. See description for more details about the product. Add to cart now!
M5 Sliding T Nut for 20 mm V-Slot Profiles
JDY-19 BLE 4.2 Module with Serial Interface
3.5'' LCD Module with Touchscreen with ILI9486 and XPT2046 Controller (320x480 px)(without MicroSD Card Slot)
Bluetooth Module Adapter with Clear Button
This module is ideal for easy control of 7-segment displays. It can also control the two points for digital clocks (seconds). See description for more details about the product. Add to cart now!
High-quality BTA16-600B TRIAC AC Voltage: 220V/110V; 50/60Hz Rated current: 5A Logic: 3.3V/5V Peak Operating Current: 8A See description for more details about the product. Add to cart now!
M5 T Nut for 20 mm V-Slot Profiles
JDY-08 backplane module Bluetooth 4.0 module BLE module CC2541 module See description for more details about the product. Add to cart now!
128x128, General 1.5inch OLED display Module See description for more details about the product. Add to cart now!
96x64 Full Color OLED Module with SSD1331 Controller
128x32, General 0.91inch OLED display Module See description for more details about the product. Add to cart now!
Suitable for 3D printer T8 lead screw. See description for more details about the product. Add to cart now!
M662 Countdown Timer Module (12 V) See description for more details about the product. Add to cart now!
SPI Interface up to 10 MHz. Implements CAN V1.2 B at up to 1 Mb/s. Arduino/ Freaduino Completely compatible. Industrial standard 9 pin sub-D connector. Standard (11 bit) and extended (29 bit) data and remote frames. See description for more details about the product. Add to cart now!
PN532 NFC module, as its name implies, is based on PN532 chip and used for 13.56MHz near field communication. The module is equipped with an onboard antenna, thus no external antenna coil is needed. See description for more details about the product. Add to cart now!
Gun for Melted Large Silicone 80 W GT-10 See description for more details about the product. Add to cart now!
Soldering Gun with Automated Solder Feeder ZD-551
M2 Self Locking Nut See description for more details about the product. Add to cart now!
This module can measure the distance to certain objects, using the principle of light reflection, measure the time traveled by the light beam from the moment of emission until it is reflected and reach back to the receiver. See description for more details about the product. Add to cart now!