The RFM69HCW is an inexpensive and...
The MMA8452 Digital Accelerometer Module is suitable for projects where you need to measure axle acceleration. The MMA8452 digital accelerometer module provides high precision at a very low current consumption of up to 165uA. It also provides I 2 C communication at frequencies up to 400kHz, the addresses being selectable according to the SA0 pin.
That product can detect motion, tilt and basic orientation. MMA8451 Triple-Axis Accelerometer has a wide usage range, from +-2g up to +-8g yet is easy to use with Arduino or another microcontroller.
The Pololu MinIMU-9 v5 is an inertial measurement unit (IMU) that packs an LSM6DS33 3-axis gyro and 3-axis accelerometer and an LIS3MDL 3-axis magnetometer onto a tiny 0.8″ × 0.5″ board.
Development Board With MPU-9250 And Atmel SAMD21 Microcontroller (Razor IMU M0)
The sensor has both I2C and SPI interfaces. It is attached to the Arduino is simple, power Vin and GND with 3-5VDC, and wire up I2C data on SCL and SDA. More advanced users can use SPI, our library has support for both. The breakout comes fully assembled and tested, with some extra header so you can use it on a breadboard.
The PJRC Motion Sensor Shield for Teensy 3.2 and Teensy-LC is designed to deliver light effects and interactive sound for small-sized props and easy-to-wear suits.
10DOF LSM6DS33, LIS3MDL and LPS25H Accelerometer, Gyroscope, Magnetometer and Digital Barometer ideal for Arduino projects offering a wide range of sensors for greater control.
This MPU6500 module integrates a 3-axis gyroscope, a 3-axis accelerometer and a DMP (Digital Motion Processor), all in one chip. MPU6500 GY Accelerometer and Gyroscope with DMP (Digital Motion Processor) embedded in a small and useful form. With the three sensors available, the projects are countless.
A gyroscope is a type of sensor that can sense twisting and turning motions. Often paired with an accelerometer, you can use these to do 3D motion capture and inertial measurement.
AltIMU-10 v5 gyroscope, accelerometer, compass and altimeter (LSM6DS33, LIS3MDL and LPS25H useful for measuring the inclination towards normal surface, acceleration, magnetic field and atmospheric pressure or altitude.
The ADXL377 is a small, thin, low power, complete 3-axis accelerometer with signal conditioned analog voltage outputs that has a full-scale range of ±200g for measuring more extreme changes in motion, shock or vibration. This board has broken out all the pins you’ll need to get the necessary data from the accelerometers.
MPU-9255 module 9DOF accelerometer, gyroscope, and magnetometer which is ideal for your projects
Module 10DOF MPU9250 and BMP280 offer 4 sensors and very useful to your project: Accelerometer, Gyroscope, Magnetometer and Digital Barometer.
This is a breakout board for InvenSense’s ITG-3200, a groundbreaking triple-axis, digital output MEMS gyroscope.
The LSM303C is a 6 Degrees of Freedom (6DOF) inertial measurement unit (IMU) in a single package, specifically developed as an eCompass device. Due to the IC housing a 3-axis accelerometer and a 3-axis magnetometer combined with its low cost, the LSM303C was perfect for us to create this small breakout board just for you.
ICM-20602 6DoF Accelerometer and Gyroscope Sensor Module
The sensor is soldered onto a PCB with four mounting holes (in case you don't remember, this is accelerating at up to 200g's!) and a 3.3V regulator so you can use it with 5v logic such as an Arduino. We also add 0.01uF filter caps for 500Hz output bandwidth.
This module is a carrier/breakout board for the ST LIS3MDL three-axis magnetometer.
BMX055 9DoF Inertial Sensor Module with SPI and I2C Interface (Accelerometer, Gyroscope and Compass)
The SparkFun ESP32 Thing is a comprehensive development platform for Espressif's ESP32, their super-charged version of the popular ESP8266. Like the 8266, the ESP32 is a WiFi-compatible microcontroller, but it adds support for Bluetooth low-power (ie BLE, BT4.0, Bluetooth Smart) and nearly 30 I / O pins.
The LIS3DH Breakout is a smart, low-power, three-axis, capacitive micro-machined accelerometer with 12 bits of resolution that you can use to add translation detection to your project. It would be classified as a 3DoF, or 3 Degrees of Freedom.
This module is based on BMF055 sensor - 16-bit triaxial accelerometer, 16-bit triaxial gyroscope, triaxial magnetometer and 32-bit M0 + cortex microcontroller. The sensor has extremely small dimensions and with this module you can use it easily.
Triple-axis accelerometer it even has an on-board 3.3V regulator, a perfect choice for interfacing with a 5V microcontroller such as the Arduino.
This breakout board makes it easy to use the tiny MMA8452Q accelerometer in your project.
Adafruit 9-DOF module and LSM9DS1 Temperature Sensor
The NXP Precision 9DoF breakout combines two of the best motion sensors we've tested here at Adafruit: The FXOS8700 3-Axis accelerometer and magnetometer, and the FXAS21002 3-axis gyroscope.
This is a breakout board for the ultra low-power LIS331HH three axis linear accelerometer. The device has a digital I2C/SPI serial interface which makes it ideal for using in embedded applications. All major pins are broken out to 0.1" spaced headers. It also includes two mounting holes as well.
The FLORA LSM303 accelerometer and compass module is small and easy to use with the FLORA board. With these two sensors you can find the position of the project and how fast it moves in 3D.
LSM303C Triaxial Accelerometer and Magnetometer Module
SparkFun Triple Axis Accelerometer (Qwiic) Breakout - MMA8452Q
The LSM6DS33 combines a digital 3-axis accelerometer and 3-axis gyroscope into a single package.
The Pololu AltIMU-10 v4 is an inertial measurement unit (IMU) and altimeter that features the same L3GD20H gyro and LSM303D accelerometer and magnetometer as the MinIMU-9 v3, and adds an LPS25H digital barometer.