Our webstore uses cookies to offer a better user experience and we recommend you to accept their use to fully enjoy your navigation.
Manufacturers
FT5617M 0.12 sec / 60° 16.9 kg * cm...
This tiny breakout board for TI’s DRV8833 dual motor driver can deliver 1.2 A per channel continuously (2 A peak) to a pair of DC motors. With an operating voltage range from 2.7 V to 10.8 V and built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature, this driver is a great solution for powering small, low-voltage...
This compact expansion board plugs directly into the GPIO header on a Raspberry Pi and provides an easy and low-cost solution for driving a pair of small brushed DC motors. Its pair of integrated MAX14870 motor drivers allows it to operate from 4.5 V to 36 V, making it a great control option for small motors that run on a wide range of voltages. The board...
A dual motor driver capable of supplying currents up to 5 A for each channel, bearing the tension between 5 V and 40 V. See description for more details about the product. Add to cart now!
This add-on board enables a compatible Raspberry Pi (Model B+ or newer), including the Pi 3 Model B+ and Model A+, to drive a pair of brushed DC motors. Its dual MC33926 motor drivers operate from 5 V to 28 V and can deliver a continuous 3 A (5 A peak) per motor. See description for more details about the product. Add to cart now!
Maximum current: 7.2A, resolution: 0.1A Subdivision range: 400~25600ppr Impulse response frequency: 200KHz DC power supply The input voltage range: 24~80VDC or AC both OK Power supply is greater than 200W. Recommend 48VDC or 48V AC Operating Temperature: -10oC~45oC See description for more details about the product. Add to cart now!
Supply Voltage: 6.8-30 VDC. Continuous Current: 13 Amp. PWM Frequency: 20 KHz. Current limiting at 30A. 3V and 5V logic level input. See description for more details about the product. Add to cart now!
This carrier board for ST’s VNH2SP30 motor driver IC operates from 5.5 to 16 V and can deliver a continuous 14 A (30 A peak). It works with 5 V logic levels, supports ultrasonic (up to 20 kHz) PWM, and features current sense feedback. Along with built-in protection against reverse-voltage, over-voltage, under-voltage, over-temperature, and over-current,...
This carrier board for ST’s VNH5019 motor driver IC operates from 5.5 to 24 V and can deliver a continuous 12 A (30 A peak). It works with 2.5 to 5 V logic levels, supports ultrasonic (up to 20 kHz) PWM, and features current sense feedback (an analog voltage proportional to the motor current). Along with built-in protection against reverse-voltage,...
If you are looking to drive two high-power motors through one compact unit, these dual VNH3SP30 motor driver carriers are perfect for you. With these boards, it’s easy to get a medium-sized, differential drive robot running in no time. See description for more details about the product. Add to cart now!
This version of our MP6500 Stepper Motor Driver Carrier with Digital Current Control ships with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. See description for more details about the product. Add to cart now!
This module is perfect for applications such as smart cars, toy cars, robots with 2.2 V to 10 V input voltage. See description for more details about the product. Add to cart now!
The AMIS-30543 stepper motor driver carrier is a Pololu carrier for ON Semiconductor's AMIS-30543 micro-stepping motor driver, which is a high-performance stepper motor driver with advanced features not found on our other stepper motor driver carriers. See description for more details about the product. Add to cart now!
This version of our MP6500 Stepper Motor Driver Carrier with Potentiometer Current Control ships with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. See description for more details about the product. Add to cart now!
This breakout board for STMicro’s STSPIN220 low-voltage microstepping bipolar stepper motor driver offers microstepping down to 1/256-step and operates from 1.8 V to 10 V, allowing stepper motors to be powered with voltages that are too low for other drivers. It can deliver up to approximately 1.1 A per phase continuously without a heat sink or forced air...
This version of our STSPIN220 Low-Voltage Stepper Motor Driver Carrier ships with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. Please see the STSPIN220 Low-Voltage Stepper Motor Driver Carrier product page for more information about the driver. See description for more...
This version of our STSPIN820 Stepper Motor Driver Carrier ships with male header pins installed, so no soldering is required to use it with an appropriate 16-pin socket or solderless breadboard. See description for more details about the product. Add to cart now!
This breakout board makes it easy to use Toshiba’s TB67S128FTG microstepping bipolar stepper motor driver, which features adjustable current limiting and microstepping down to 1/128-step. In addition, it has the ability to dynamically select an optimal decay mode by monitoring the actual motor current, and it can automatically reduce the driving current...
This tiny breakout board for TI’s DRV8801 provides a modern alternative to classic motor drivers such as the L293D, SN754410, and L298N. It can deliver a continuous 1 A (2.8 A peak) to a single motor and offers a wide operating voltage range of 8 V to 36 V. The DRV8801 features a simple two-pin speed/direction interface, current-sense feedback, and...
This tiny breakout board for TI’s DRV8838 motor driver can deliver a continuous 1.7 A (1.8 A peak) to a single brushed DC motor. With an operating voltage range from 0 V to 11 V and built-in protection against reverse-voltage, under-voltage, over-current, and over-temperature, this driver is a great solution for powering a small, low-voltage motor. See...
TB6600 4A 42V Motor Driver Controller See description for more details about the product. Add to cart now!
BA6109 - Motor Driver 18 V, 0.8 A DR MOTOR 3-MODE 18 V 0.8 A
BA6209 - Dual Reversible Motor Driver 18 V, 1.6 A DR MOTOR 4-MODE 18 V 1.6 A
BA6229 - Motor Driver 24 V, 1.2 A DR MOTOR 4-MODE 24 V 1.2 A
BA6238A - Dual Reversible Motor Driver, 20 V MOTOR DR 2X REV 20 V
BA6239A - Dual Reversible Motor Driver, 20 V MOTOR DR. 2XREV. 20 V
Crank up your robotics with a powerful Adafruit DRV8871 motor driver breakout board. This motor driver has a lot of great specs that make it useful for a wide variety of mechatronics. See description for more details about the product. Add to cart now!
This compact breakout board makes it easy to use Allegro’s A4990 dual motor driver, which can control two bidirectional DC motors over a wide operating voltage range of 6 V to 32 V. It is capable of delivering a continuous 0.7 A to each motor channel, and onboard sense resistors enable the A4990 to limit the peak motor current to about 0.9 A per channel....